Weidmuller WI-I/O-9-U2: Wireless Mesh I/O & Gateway User Manual de usuario Pagina 4
- Pagina / 126
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
3
FCC Notice:
This WI-I/O 9-U2 module uses the “E2_900M Wireless Data Modem” radio and complies
with Part 15.247 of the FCC Rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference
This device must accept any interference received, including interference that may
cause undesired operation.
WI-I/O 9-U2 Radio Telemetry Unit must be installed in a suitable enclosure that provides
mechanical, shock and fire hazard protection.
This device must be operated as supplied by WEIDMULLER. Any changes or modifications
made to the device without the written consent of WEIDMULLER may void the user’s
authority to operate the device.
This device must be installed by professional installers in compliance with 47 CFR Part 15
Subpart C Section 15.203 and 15.205, who will be responsible for maintaining EIRP no
greater than 36 dBm in accordance with 47 CFR Part 15 Subpart C Section 15.247 (b)(2)(4).
In accordance with 47 CFR Part 15 Subpart C Section 15.203 only the following
antenna/coax cable kits combinations can be used.
Manufacturer
Model Number
Coax Kit
Net
WEIDMULLER
6720005236
6720005253
5dB Gain
WEIDMULLER
6720005236
6720005255
2dB Gain
WEIDMULLER
6720005235
6720005253
2dB Gain
WEIDMULLER
6720005235
6720005255
-1dB Loss
WEIDMULLER
6720005221
6720005255
4dB Gain
WEIDMULLER
6720005089
Includes 5m Cellfoil
Unity Gain
WEIDMULLER
6720005086
Includes 1m Cellfoil
-2dB Loss
Part 15 –This device has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part15 of the FCC rules (Code of Federal Regulations
47CFR Part 15). Operation is subject to the condition that this device does not cause
harmful interference.
Notice – Any changes or modifications not expressly approved by WEIDMULLER
could void the user’s authority to operate this equipment.
This Device should only be connected to PCs that are covered by either FCC DoC or are
FCC certified.
- Industrial Wireless MESH I/O 1
- WI-I/O 9-U2 MESH I/O 1
- 804.794.2877 Main 2
- 804.794.0252 Fax 2
- Industry Canada: 3
- FCC Notice: 4
- Hazardous Location Notices: 5
- IMPORTANT Notice: 6
- TABLE OF CONTENTS 7
- TABLE OF FIGURES 11
- Chapter 1 - Introduction 13
- 1.2 Module Structure 15
- 1.3 Getting Started 16
- Chapter 2 - Installation 17
- 2.2.2 Expansion I/O Supply 19
- 2.2.3 Internal I/O 20
- 2.2.4 Grounding 20
- 2.3 Radio 21
- 2.4 Antenna 22
- Yagi antennas 26
- 2.5 Connections 27
- WI-IO 9-U2 28
- “Factory Boot” switch 29
- USB Host port 29
- Dipswitches 29
- Front panel connections 30
- Figure 16 - Fail-Safe State 33
- 2.5.5 Analog Inputs 34
- Single Ended Voltage Inputs 36
- 2.5.6 Analog Outputs 37
- Chapter 3 - Operation 38
- Digital Inputs 39
- Digital Outputs 39
- ETHERNET 40
- LINK100M 40
- 3.3 System Design 41
- 3.3.4 Design for Failures 42
- Fail-to-transmit alarm 43
- Fail-to-receive alarm 43
- 3.4 WIBMesh 44
- Chapter 4 - Configuration 46
- Figure 23 – Network Settings 47
- Figure 24 - Ping 47
- Figure 26 - IP Gateway Mode 49
- Figure 27 - Default Gateway 49
- Figure 28 -IP Address Range 49
- Figure 29 - Routing Rule 50
- 4.3 Module Configuration 51
- Re-Open Previous Project 52
- 4.3.2 Configuration Screens 53
- 4.3.3 Project Screen 54
- 4.3.4 Adding Units 54
- Unit Details 55
- 4.3.5 Mappings 56
- Write Mapping 57
- Gather Scatter Mapping 57
- Read Mappings 57
- Example configuration 60
- 4.3.7 Address Map 61
- 4.3.9 I/O Configuration 62
- Pulsed Outputs 63
- Analog Inputs 64
- Analog Outputs 65
- Adding modules 65
- (selected on the rotary 66
- 4.3.11 Failsafe Blocks 67
- “Invalid” register state 68
- 4.3.12 Sensitivity Blocks 69
- 4.3.13 Serial Configuration 70
- Serial - Expansion I/O 71
- 4.3.14 Modbus Configuration 72
- Mapping parameters 73
- Modbus TCP Mapping Examples 75
- Modbus RTU Master 75
- Modbus RTU 76
- Master Example 76
- 4.4 Web based Configuration 77
- Figure 62 - Neighbour RSSI 79
- 4.4.3 IP Routing 80
- 4.4.4 Radio Settings 81
- 4.4.5 Mesh Fixed Routes 82
- Example #1 83
- Example #2 84
- Writing Configuration File 87
- System Log File 87
- Reading Configuration File 87
- Figure 73 - Format USB 88
- Figure 74 - Quick Format 88
- Figure 75 - Firmware Files 88
- Figure 76- firmware version 89
- Product Reconfiguration 90
- Demonstration Mode 91
- Feature Licence Keys 91
- Chapter 5 - Diagnostics 92
- 5.1.1 Watchdog Error Log 93
- 5.2 Connectivity (WibMesh) 95
- 5.4 Neighbour RSSI (WibMesh) 97
- Figure 87 - Multipath Fading 98
- Trace Route 100
- 5.7 Monitor Comms 103
- Chapter 6 - Specifications 108
- “Output Coils” 112
- “Input Bits” 112
- “Input Registers” 113
- “Holding Registers” 114
- 115 116
- 118 119
- 119 120
- 120 121
- 121 122
- 122 123
- 123 124
© 2020, manymanuals.es. Todos los derechos reservados | 0.116 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales