Weidmuller WI-I/O-9-U2: Wireless Mesh I/O & Gateway User Manual de usuario Pagina 115
- Pagina / 126
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
114
Appendix C: Expansion I/O Registers
Adding Expansion I/O modules to the WI-I/O 9-U2 will automatically add
the I/O from the WI-I/O-EX-1-S modules to the internal WI-I/O 9-U2 I/O
store.
To calculate the register location in the I/O Store find the address of the
I/O point in the tables below and add the offset.
The Offset is the Modbus address multiplied by 20.
E.g1. Digital input #1 on an WI-I/O-EX-1-S-11 with address 5 would be: (5x20)
+10001 = 10101
E.g2. Digital output #2 on an WI-I/O-EX-1-S-11 with address 6 would be: (6x20) +2
= 122
E.g3. Analog input #3 on an WI-I/O-EX-1-S-12 with address 3 would be: (3x20)
+30003 = 30063.
E.g4. Analog Output #8 on an WI-I/O-EX-1-S-13 with address # 7 would be: (7x20)
+ 40007 = 40147
I/O store for a WI-I/O-EX-1-S-11 Expansion I/O module
0001 + Offset
0016 + Offset
DIO Outputs 1 - 16
10001 + Offset
10016 + Offset
DIO Inputs 1 - 16
10019 + Offset
Modbus Comms Fail indication for this WI-I/O-EX-1-S module
10020 + Offset
Modbus Comms Fail indication (Inverse) for this WI-I/O-EX-1-S
module
30001 + Offset
30004 + Offset
WI-I/O-EX-1-S-11 pulsed input rate 1 – 4
30005 + Offset
30012 + Offset
WI-I/O-EX-1-S-11 Pulsed input count
30017 + Offset
Modbus Error Counter for this WI-I/O-EX-1-S module
30018 + Offset
Modbus Last Error Code for this WI-I/O-EX-1-S module. (Section
5.1.3
30019 + Offset
Modbus Lost Link Counter for this WI-I/O-EX-1-S module
30020 + Offset
Module type (0x0101) = 257. / Error Status
40009 + Offset
40016 + Offset
Pulsed Output target 1 – 8 (1 register per pulsed output)
- Industrial Wireless MESH I/O 1
- WI-I/O 9-U2 MESH I/O 1
- 804.794.2877 Main 2
- 804.794.0252 Fax 2
- Industry Canada: 3
- FCC Notice: 4
- Hazardous Location Notices: 5
- IMPORTANT Notice: 6
- TABLE OF CONTENTS 7
- TABLE OF FIGURES 11
- Chapter 1 - Introduction 13
- 1.2 Module Structure 15
- 1.3 Getting Started 16
- Chapter 2 - Installation 17
- 2.2.2 Expansion I/O Supply 19
- 2.2.3 Internal I/O 20
- 2.2.4 Grounding 20
- 2.3 Radio 21
- 2.4 Antenna 22
- Yagi antennas 26
- 2.5 Connections 27
- WI-IO 9-U2 28
- “Factory Boot” switch 29
- USB Host port 29
- Dipswitches 29
- Front panel connections 30
- Figure 16 - Fail-Safe State 33
- 2.5.5 Analog Inputs 34
- Single Ended Voltage Inputs 36
- 2.5.6 Analog Outputs 37
- Chapter 3 - Operation 38
- Digital Inputs 39
- Digital Outputs 39
- ETHERNET 40
- LINK100M 40
- 3.3 System Design 41
- 3.3.4 Design for Failures 42
- Fail-to-transmit alarm 43
- Fail-to-receive alarm 43
- 3.4 WIBMesh 44
- Chapter 4 - Configuration 46
- Figure 23 – Network Settings 47
- Figure 24 - Ping 47
- Figure 26 - IP Gateway Mode 49
- Figure 27 - Default Gateway 49
- Figure 28 -IP Address Range 49
- Figure 29 - Routing Rule 50
- 4.3 Module Configuration 51
- Re-Open Previous Project 52
- 4.3.2 Configuration Screens 53
- 4.3.3 Project Screen 54
- 4.3.4 Adding Units 54
- Unit Details 55
- 4.3.5 Mappings 56
- Write Mapping 57
- Gather Scatter Mapping 57
- Read Mappings 57
- Example configuration 60
- 4.3.7 Address Map 61
- 4.3.9 I/O Configuration 62
- Pulsed Outputs 63
- Analog Inputs 64
- Analog Outputs 65
- Adding modules 65
- (selected on the rotary 66
- 4.3.11 Failsafe Blocks 67
- “Invalid” register state 68
- 4.3.12 Sensitivity Blocks 69
- 4.3.13 Serial Configuration 70
- Serial - Expansion I/O 71
- 4.3.14 Modbus Configuration 72
- Mapping parameters 73
- Modbus TCP Mapping Examples 75
- Modbus RTU Master 75
- Modbus RTU 76
- Master Example 76
- 4.4 Web based Configuration 77
- Figure 62 - Neighbour RSSI 79
- 4.4.3 IP Routing 80
- 4.4.4 Radio Settings 81
- 4.4.5 Mesh Fixed Routes 82
- Example #1 83
- Example #2 84
- Writing Configuration File 87
- System Log File 87
- Reading Configuration File 87
- Figure 73 - Format USB 88
- Figure 74 - Quick Format 88
- Figure 75 - Firmware Files 88
- Figure 76- firmware version 89
- Product Reconfiguration 90
- Demonstration Mode 91
- Feature Licence Keys 91
- Chapter 5 - Diagnostics 92
- 5.1.1 Watchdog Error Log 93
- 5.2 Connectivity (WibMesh) 95
- 5.4 Neighbour RSSI (WibMesh) 97
- Figure 87 - Multipath Fading 98
- Trace Route 100
- 5.7 Monitor Comms 103
- Chapter 6 - Specifications 108
- “Output Coils” 112
- “Input Bits” 112
- “Input Registers” 113
- “Holding Registers” 114
- 115 116
- 118 119
- 119 120
- 120 121
- 121 122
- 122 123
- 123 124
© 2020, manymanuals.es. Todos los derechos reservados | 0.102 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales